18 Dodge Ram Diesel 67 Engine Coolant Bleeding Tips
Bleeding coolant on your 18 Dodge Ram Diesel 6.7 engine is essential to remove trapped air and prevent overheating. This guide walks you through every step, from spotting air lock symptoms to completing a full coolant flush. You will learn simple tricks, common mistakes, and expert tips that save time and money.
There is nothing worse than stepping out to your truck on a hot morning and seeing the temperature gauge climbing into the red. If you own a 2018 Dodge Ram with the 6.7 Cummins diesel engine, you already know how much power this truck packs. But all that power generates serious heat, and the cooling system has to work hard to keep everything in check. When air gets trapped inside the cooling system, it creates what mechanics call an air lock. This tiny pocket of air can cause big problems if you do not fix it quickly.
Coolant bleeding is the process of removing that trapped air from your engine’s cooling passages. It is one of those jobs that seems small but makes a huge difference. Whether you just replaced a hose, flushed the system, or noticed your heater blowing lukewarm air, bleeding the coolant on your 18 Dodge Ram Diesel 6.7 engine is a skill every truck owner should know. In this guide, we will walk you through the entire process step by step. You will learn what to look for, what tools to grab, and how to avoid the mistakes that trip up even experienced truck owners.
Key Takeaways
- Air in the cooling system causes real damage: Trapped air leads to overheating, poor heater output, and potential engine failure on your 18 Dodge Ram Diesel 6.7.
- Know the warning signs early: Bubbling in the reservoir, inconsistent temperature gauge readings, and gurgling sounds all point to air locks.
- The right tools make the job easy: A catch pan, funnel, distilled water, and the correct coolant type are all you need to start.
- Follow the proper bleed sequence: Opening the bleed screw at the right time and running the engine in stages ensures all air escapes.
- Avoid common pitfalls: Overfilling the reservoir, skipping the thermostat check, and rushing the process cause repeat problems.
- Regular maintenance pays off: Flushing the cooling system every 2 years keeps your diesel engine running cool and reliable.
📑 Table of Contents
- Why Coolant Bleeding Matters for Your 18 Dodge Ram Diesel 6.7
- Signs Your Cooling System Has Air in It
- Tools and Supplies You Will Need
- Step-by-Step Coolant Bleeding Process
- Common Mistakes to Avoid When Bleeding Coolant
- Expert Tips for Long-Term Cooling System Health
- When to See a Professional Mechanic
- Conclusion
Why Coolant Bleeding Matters for Your 18 Dodge Ram Diesel 6.7
The cooling system in your 6.7 Cummins diesel engine is a closed loop. Coolant flows through the engine block, picks up heat, moves to the radiator, and then cycles back again. The water pump pushes the coolant through the system, and the thermostat regulates the flow based on engine temperature. Everything works smoothly as long as the system stays full of liquid coolant and free of air.
Here is the problem. Air is compressible, while coolant is not. When a pocket of air gets trapped in a cooling passage, the water pump spins but cannot push that air through the system the same way it pushes liquid. This creates what is called an air lock. The coolant stops flowing properly in that area, and the engine starts to overheat, even if the radiator is full. On a diesel engine like the 6.7 Cummins, overheating can lead to warped heads, blown head gaskets, and very expensive repairs.
How Air Gets Into the Cooling System
Air can enter the cooling system in several ways. After any coolant flush or refill, small air bubbles can get trapped in the engine block and radiator hoses. A loose coolant hose connection can let air seep in slowly over time. A failing head gasket can actually pull air into the cooling system from the combustion chamber. Even a cracked radiator cap that does not seal properly can allow air to enter as the system cools down and creates a vacuum.
On the 18 Dodge Ram Diesel 6.7, the cooling system design includes a bleed screw that helps you release trapped air. However, not everyone knows where it is or how to use it properly. That is exactly what this guide is for.
Signs Your Cooling System Has Air in It
Catching an air lock early saves you from a roadside breakdown. Your truck gives you clear warning signs when air gets into the cooling system. Here are the most common symptoms to watch for.
Bubbling in the Coolant Reservoir
Open the coolant reservoir cap when the engine is cool. Look closely at the coolant. If you see small bubbles rising through the liquid, that is air escaping from the engine block. A few tiny bubbles are normal. But if the coolant looks like it is boiling even when the engine is cold, you have an air lock problem.
Inconsistent Temperature Gauge Readings
Your temperature gauge should sit steady in the normal range when driving. If it bounces between normal and hot, or if it spikes suddenly and then drops, air pockets are moving through the cooling system. The gauge reacts to the air because air does not transfer heat the same way liquid coolant does.
Weak or Lukewarm Heater Output
The heater core is part of the cooling system. It relies on hot coolant flowing through it to produce warm air. When air gets trapped in the heater core, you lose heat. If your heater blows cold air even when the engine is warm, air in the system is a likely culprit.
Coolant Leaking from the Overflow Tube
When air pressure builds up in the cooling system, it pushes coolant out through the overflow hose. If you notice a green or orange puddle under your truck or coolant dripping from the overflow tube, the system may have an air lock causing excess pressure.
Tools and Supplies You Will Need
Bleeding coolant on your 18 Dodge Ram Diesel 6.7 does not require a garage full of tools. You need a few basic items and the right coolant type. Here is what to gather before you start.
- Dexcool or equivalent 50/50 pre-mixed coolant: The 6.7 Cummins diesel engine uses a specific coolant formulation. Check your owner’s manual for the exact specification.
- Distilled water: If you are mixing coolant yourself, always use distilled water. Tap water contains minerals that can clog passages and cause corrosion.
- A catch pan: You will need a large pan to catch old coolant when you drain the system. Used coolant is toxic and must be disposed of properly.
- A funnel: A narrow funnel makes it easy to fill the radiator and reservoir without spilling.
- A clean rag or towel: Coolant can stain clothing and damage paint. Keep rags handy for drips and spills.
- A wrench or socket: You need the right size tool to open the bleed screw on the cooling system.
- Safety glasses and gloves: Coolant is toxic to animals and can irritate your skin. Protect yourself before you start.
Step-by-Step Coolant Bleeding Process
Now that you have your tools ready, let us walk through the bleeding process. This method works specifically for the 2018 Dodge Ram with the 6.7 Cummins diesel engine. Follow each step carefully for the best results.
Step 1: Let the Engine Cool Completely
Never work on a hot cooling system. The coolant inside is under pressure and can cause severe burns. Wait at least two hours after driving, or let the engine cool overnight. The radiator cap should only be removed when the engine is completely cold.
Step 2: Drain the Old Coolant
Place your catch pan under the radiator drain valve. Open the valve and let the old coolant drain out completely. Once the flow stops, close the valve. At this point, you can also remove the lower radiator hose to drain any remaining coolant from the engine block.
Step 3: Flush the System
If you are replacing the coolant or noticed sludge in the old fluid, flush the system now. Fill the radiator with distilled water, run the engine for 10 minutes, and then drain again. Repeat this until the water runs clear. A clean system allows the new coolant to flow freely and helps you spot any remaining air pockets.
Step 4: Locate the Bleed Screw
On the 18 Dodge Ram Diesel 6.7, the coolant bleed screw is typically located on the thermostat housing or near the upper radiator hose connection. Look for a small bolt or screw on the top of the engine block near the front. Refer to your service manual if you have trouble finding it.
Step 5: Open the Bleed Screw and Fill the System
With the bleed screw open, slowly pour the new coolant mixture into the radiator using a funnel. Keep filling until you see coolant coming out of the bleed screw with no air bubbles. This is the key moment. The fluid should flow steadily and smoothly. If you see bubbles, keep adding coolant and wait for them to stop.
Step 6: Close the Bleed Screw and Top Off the Reservoir
Once the coolant flows without bubbles, tighten the bleed screw securely. Fill the coolant reservoir to the full cold line. Do not overfill. Leave a small gap at the top to allow for expansion as the engine warms up.
Step 7: Run the Engine and Check for Air Locks
Start the engine and let it idle with the heater turned on full blast. Watch the temperature gauge closely. The thermostat will open and close as the engine reaches operating temperature. You may see the gauge climb slightly higher than normal as remaining air pockets move through the system. This is normal. Let the engine run for 15 to 20 minutes. If the gauge stays steady and the heater blows hot air, you have successfully bled the cooling system.
Step 8: Recheck the Coolant Level After the Engine Cools
After the engine cools down completely, open the radiator cap and check the coolant level. Top off if needed. Also check the reservoir level and adjust to the full cold mark. Run the engine one more time and recheck the temperature gauge. A steady needle means the job is done right.
Common Mistakes to Avoid When Bleeding Coolant
Even experienced truck owners make mistakes when bleeding coolant. These errors can lead to repeat air locks, overheating, or damage to the cooling system. Here are the most common ones to watch out for.
Overfilling the Coolant Reservoir
It is tempting to fill the reservoir all the way to the top. But coolant expands when it heats up. If you overfill, the excess coolant has nowhere to go and can push out through the overflow hose or even leak past seals. Always fill to the full cold line and let the system find its own level.
Skipping the Thermostat Check
A stuck thermostat is one of the leading causes of overheating in the 6.7 Cummins diesel engine. If your thermostat is stuck closed, coolant cannot circulate properly, and no amount of bleeding will fix the problem. Before you bleed the system, make sure the thermostat opens and closes freely.
Using the Wrong Coolant Type
The 2018 Dodge Ram 6.7 Cummins requires a specific coolant formulation. Mixing different coolant types can cause chemical reactions that create sludge and clog the cooling passages. Always use the coolant recommended by Ram for your diesel engine.
Rushing the Bleed Process
Bleeding coolant takes patience. If you rush through the steps, you will leave air pockets trapped in the system. Take your time. Watch for bubbles. Let the engine warm up and cool down between checks. A slow and steady approach gets the best results.
Forgetting to Check the Radiator Cap
A faulty radiator cap can cause all kinds of cooling system problems. The cap maintains the correct pressure in the system, which raises the boiling point of the coolant. If the cap seal is worn or cracked, air gets pulled into the system as it cools. Replace the radiator cap if it is more than a few years old or shows any signs of damage.
Expert Tips for Long-Term Cooling System Health
Bleeding coolant is not a one-time job. Keeping your 18 Dodge Ram Diesel 6.7 cooling system in top shape requires regular attention. Here are expert tips that help you avoid problems down the road.
Flush the Cooling System Every 2 Years
Over time, coolant breaks down and loses its ability to transfer heat effectively. Old coolant also becomes acidic and can corrode metal parts inside the cooling system. Flushing the system and replacing the coolant every two years keeps everything flowing smoothly and protects your engine from overheating.
Inspect Hoses and Connections Regularly
Coolant hoses get brittle with age. A cracked hose can leak coolant slowly, letting air seep into the system. Inspect all hoses and clamps every few months. Replace any hose that feels spongy, cracked, or soft. A few dollars on a new hose saves hundreds on engine repairs.
Watch Your Coolant Color and Condition
Healthy coolant is bright green, orange, or pink depending on the type. If your coolant looks rusty, dark brown, or has particles floating in it, it is time for a flush. Dirty coolant cannot flow properly through the cooling system and increases the risk of air locks and overheating.
Keep an Eye on the Temperature Gauge
Your temperature gauge is your best early warning system. If you notice any changes in how the gauge behaves, do not ignore it. A gauge that climbs higher than usual or fluctuates more than normal often points to an air lock or a cooling system issue that needs attention right away.
Use the Right Tools for the Job
A coolant pressure tester can help you find slow leaks that are hard to see with the naked eye. A vacuum filler tool makes it easy to bleed air from the system without the mess of open pouring. Investing in a few simple tools makes coolant maintenance faster and easier every time.
When to See a Professional Mechanic
Most coolant bleeding jobs are straightforward and can be done at home with basic tools. However, some situations call for a professional mechanic. If you bleed the system and the temperature gauge still climbs into the red, there may be a deeper problem. A blown head gasket, a cracked engine block, or a failing water pump can all cause persistent overheating that no amount of bleeding will fix.
Also, if you notice a sweet smell inside the cab, white smoke from the exhaust, or coolant mixing with your engine oil, stop driving immediately. These are signs of a serious internal leak that needs professional diagnosis. Trying to drive on a damaged cooling system can destroy your engine in a matter of minutes.
Conclusion
Bleeding the coolant on your 18 Dodge Ram Diesel 6.7 engine is a simple but important maintenance task. It removes trapped air, prevents overheating, and keeps your truck running at the right temperature. By following the steps in this guide, you can handle the job yourself and save money on shop visits. Remember to watch for the warning signs of an air lock, use the right coolant, and never rush the process. A little patience and attention to detail go a long way toward keeping your 6.7 Cummins diesel engine cool and reliable for miles to come. Take care of your cooling system, and it will take care of your engine.
Frequently Asked Questions
How do I know if my 18 Dodge Ram Diesel 6.7 has an air lock in the cooling system?
Look for bubbling in the coolant reservoir, a temperature gauge that rises and falls unpredictably, weak heater output, or coolant pushing out through the overflow hose. These are the most common signs of trapped air in the cooling system. If you notice any of these symptoms, bleeding the coolant should be your first step.
Can I drive my 2018 Dodge Ram 6.7 Cummins with air in the cooling system?
You should not drive the truck if you suspect an air lock. Air in the cooling system prevents proper heat transfer, which can cause the engine to overheat quickly. Overheating a diesel engine can lead to serious and expensive damage. Bleed the coolant before you drive the truck for any extended distance.
How long does it take to bleed coolant on a 6.7 Cummins diesel engine?
The entire process takes about 30 to 45 minutes for most owners. This includes draining the old coolant, flushing the system, refilling with fresh coolant, and running the engine to release trapped air. If you are new to the process, give yourself extra time to be careful and thorough.
What type of coolant does the 18 Dodge Ram Diesel 6.7 use?
The 2018 Dodge Ram 6.7 Cummins diesel engine requires a specific coolant formulation, typically a high-quality extended-life coolant that meets the manufacturer’s specifications. Always check your owner’s manual or consult a dealer to confirm the exact coolant type. Using the wrong coolant can cause corrosion and cooling system problems.
Why does air keep getting into my cooling system after I bleed it?
If air keeps returning after you bleed the system, there is likely a leak somewhere. Check all coolant hoses, the radiator cap, the water pump seals, and the heater core connections for leaks. A failing head gasket can also pull air into the cooling system from the combustion chamber. Finding and fixing the leak is essential to keeping air out of the system.
Is it necessary to bleed the cooling system after a coolant flush?
Yes, absolutely. Every time you drain and refill the cooling system, air pockets get trapped in the engine block and radiator. Bleeding the system after a flush removes those air pockets and ensures coolant flows properly through all passages. Skipping this step is one of the most common causes of overheating after a coolant change.
